Originally Posted by Bill Fitzmaurice It’s called bi-wiring. It doesn’t actually do anything, but enough people think that it does so that some manufacturers use bi-wire terminals to placate them, rather than lose sales. Connect the top to bottom with jumpers, use one wire to the receiver. It does do something Bill. Originally Posted by cel And don’t forget. It helps high end audio shops sell more expensive speaker cables This is all true enough as far as it goes, but there are some constructive options here as well. None are easy, but the blanket rejection of any positive use of these two pairs of inputs is incomplete. Normally, these speaker terminals would have been connected at the factory by use of a strapping bar: The straps must be missing here.

Please turn JavaScript on and reload the page.

I have this sub: I wired the sub in series first, and it sounded too Now it sounds stronger, but still not quite strong enough for, supposedly, watts rms. I hooked up my watts home subwoofer in my car before, and it sound just as strong if not stronger What’s with the two sets of terminals on the monoblock? Since I didn’t wire it in series, or in parallel, what do you call the way that I wired it?

What would happen if I ran this sub on 2 ohms from the amp when the sub is supposed to be 1 or 4?

If you’re ready to dive into home theater with a single purchase, the Cinema ProPack offers great sound and excellent components.

Place it optimally in any room without wires or clutter. It is also equipped with optical and analog audio inputs. No more loud commercials—Harman Volume keeps your sound levels consistent Harman Volume makes sure that sudden volume changes—such as commercials—will be smooth and consistent. Big movie sound with Dolby Digital and Harman Display Surround sound Harman Display Surround sound and Dolby Digital decoding fill your room with movie sound and music, not speakers and wires. Stream music from your smartphone or tablet with Bluetooth wireless audio The JBL Cinema SB remembers up to 10 Bluetooth devices and can instantly reconnect for music streaming.

Stunning home theater sound with a wireless subwoofer Designed to perfectly match any TV, the Cinema SB projects stunning, virtual surround sound from a sleek and simple package. It connects wirelessly to its compact, powerful subwoofer, and connects with a single cable to a TV. It also can play music wirelessly from Bluetooth smartphones or tablets.

JBL WR2.4 Wireless Headphones Review

Follow these step-by-step instructions to attach speakers to your computer Step 1: Ensure that the computer is turned off. Plug the speakers into the power socket.

These are usually connected in one of two ways and these are illustrated in the next graphic.

Gene Yes, they will. Joe At Customer Service Date published: Yes, if your computer has the drivers for A2DP stereo audio streaming via Bluetooth, this should work. The monitor probably does not feature software drivers. You should be aware that you may have delay in the audio signal, which may make this application impossible to use with video material.

Bo Harman How to connect Bluetooth? If a headphone is inserted while streaming music via Bluetooth, it will mute speakers, leaving only sound in the headphones. If no audio signal is present for approximately ten minutes, the speakers will go into power-standby mode and the LED will turn off. Joe G at Customer Service Date published: Sheryl Hello, Thank you for the inquiry.

Place speakers into pairing mode and search available Bluetooth devices on the IPad. If the issue is unresolved please contact our support center at for warranty process information. AaronG Hello, Thank you for the inquiry. These are computer speakers and are not designed to connect with other peripherals.

Tips for Hooking Up Speakers

How to hook up a subwoofer to a stereo system Hint: You don’t necessarily need a receiver with subwoofer output jacks. Subs can provide a foundation to the sound that few speakers can muster on their own. So adding a sub is not just about adding more and deeper bass; rather, a properly integrated subwoofer can improve the overall sound of the system.

There is a reason why an open-air Tiesto stadium show will have speaker towers the size of small houses — Tiesto wants to reach 50, people, and he knows you need lots of big speakers to do that.

Speaker Connections for proper impedance match A note about amplifiers: You should always use the recommended load for your amplifier. However, if you must use a load other than the recommended load, here is a short guide. Most solid-state amplifiers would rather look at an open circuit no speaker at all than a load. Therefore, you can usually use a load that is higher than the recommended load. Do not use a lower impedance load, as this could cause serious damage to your SS amp.

On the other hand, most tube amplifiers need a load to avoid transformer or tube socket damage. If a mismatch can not be avoided on a tube amp, it is better to go towards a lower impedance rather than too high of a speaker impedance. This may stress the tubes some, but, tubes are cheaper than transformers. As the graphic shows, you connect the positive wire to speaker A’s positive terminal, connect a wire from speaker A’s negative terminal to speaker B’s positive wire, and then connect the negative wire to the negative terminal of speaker B.

You could continue this string for as many speakers that you have available, however, it may not be very practical. The impedances add in a series connection. If speaker A equals 8ohms and speaker B equals 8ohms, the total load is A plus B, or 16ohms. If you string three 8 ohm speakers in series the net impedance will be 3X8 24 ohms.

Jbl Professional

David David, did you heare someting new concerning your popping sound in subwoofer? I do have excact the same problem. They have tryed to update the subwoofer twice, but with no effect. Authorized service center in Denmark. I’m aware that many have the same problem. If this doesn’t resolve the issue ,Please submit a case request at https:

Joe At Customer Service Date published:

Directly streaming audio over a 2. The main advantage to this setup is compatibility. You can easily hook up wireless headphones to your TV, computer, home audio system, or non-bluetooth mp3 player. The main disadvantage is that the base station is plugged into the wall, so you lose out on the portability function. The headband is adjustable and will fit the largest of heads.

The headphones are surprisingly lightweight, which is attributed to their plasticky, yet pretty durable, build. The volume is independent from your audio source volume. The battery lasts 8 hours and charges when you place it on the dock. The audio quality is really good, with a little room for improvement. The audio quality is really clear especially considering the wireless range.

The mids are well balanced and the highs are pretty decent.

need help to hook up JBL car amplifier using SMPS at home

Share on Facebook Your computer experience is made up by three things: Any one of those three can keep you from being completely immersed in your program. Of the three, sound is the simplest to fix by exchanging external speakers for the speakers provided with your computer. All you have to do to add speakers is plug them in and turn on the speakers and the sound on your computer.

In most cases, you should also have a cord which will connect your speakers to a power source such as a wall outlet or surge protector.

Last updated 13 November, 26 Very different to the type of amplifier you may have in your home stereo, PA power amplifiers are designed to run at high levels for long periods of time. In the first part of this four-part series we looked at the basic elements you need to know about when it comes to DJ PA systems. In the second part , we carried on laying the groundwork by answering some common newbie questions. It is vital that the amplifier can supply sufficient power for your speakers say W , but your speakers also need to be able to handle this amount of power.

So if you have the amplifier with W but your speakers are only made for W, they will die on you rather soon. So I always recommend to shop for amplifier and speakers together. Alternatively, you could go for active speakers. These have the power amplifier built in and the manufacturer has already done the job of matching the amplifier s to the speaker s , so you no longer need to worry about it.

Now, a PA amplifier is very different from a hi-fi amplifier.